Print

MERCIA has 12 registers in total. Since there are only three bits for register encoding are available in the instruction, seven (1-7) registers can be addressed by the user. Five more registers (8-12) can be addressed by the Microcode. The last three (13-15) are virtual registers. They are used to connect the results of the binary to 7-segment encoder to the databus.

       

 

Source

 

 

Destination

 

 

Code

Letter

Register

left

Clear

right

left

Clear

right

0

0000

-

Not used

-

-

-

-

-

-

1

0001

a

Data a

data

clear

address

data

clear

address

2

0010

b

Data b

data

clear

address

data

clear

address

3

0011

c

Data c

data

clear

address

data

clear

address

4

0100

g

General purpose

data

clear

address

data

clear

address

9

0101

t

Temporary store

data

clear

decoder

data

clear

decoder

5

0110

d

Data pointer

data

clear

address

data

clear

address

7

0111

r

Return address

data

clear

address

data

clear

address

8

1000

j

Jump base

data

clear

address

data

clear

address

6

1001

p

Program pointer

data

clear

address

data

clear

address

10

1010

i

Instruction register

data

clear

-

data

clear

-

11

1011

m

Memory register

data

clear

 

data

clear

-

12

1100

s

Status register

-

-

-

data

clear

-

13

1101

1

Binair to 7-segment MSB

-

-

-

signed

clear

data

14

1110

2

Binair to 7-segment

-

-

-

hex

-

data

15

1111

3

Binair to 7-segment LSB

-

-

-

-

-

data

 

Register usage


Data a, b and c

These registers are mainly used to facilitate the ALU. Unary operations are operations with one operand that uses a source and a destination register. Binary operations are operations with two operands that uses three registers: two for the input values and one for the result.

In the ALU command it is possible to define which of the three registers to use for input an which for output.

General purpose

This general purpose register can be freely used.

Temporary store

This register feeds the binary to 7-segment display encoder and is use by the Microcode to store intermediate results. 

Data pointer

This register is used for array structures, where a pointer to the data is needed.

Program pointer

This register contains the value of the next program step to be executed.

Return address

If the execute command is performed, this register stores the return address. If multiple return addresses are needed this can be programmed, since this register can be accessed by the computer program.

Jump base

This register enables the relative addressing and stores the first byte (byte 0) of the program. If this register is zero, absolute addressing is used. 

Instruction register

This register contains the current executed command.

Memory register

The memory register is used as a buffer for the memory.

Status register

The status register contains a number of status flags as discussed in the corresponding paragraph.

Register control


There are two issues that have to be addressed for register usage. First there is relay rumble, or the possibility that the output of a relay circuit will change a few times from 0 to 1 and vice versa, before all the relays have taken their final switching position. If this rumble produces a 1 before the final 0, the register will be set to 1, regardless the final value of the circuit. Secondly, a register can only be written when it is previously cleared en contains solely zeros.

Both issues can be solved in a very elegant way as shown in the circuit diagram below. The solution lies in a delay in the enabling of the registers whilst clearing the destination register at the same time.

 This enables the following sequence:

  1. The enable signal is set to 1. At the same time the clear signal of the destination register is set to 1.
  2. Then clear relay is activated and as a result of that the destination register is cleared.
  3. The register switch is set open, enabling the register.
  4. The feedback loop of the register is not enabled because the clear relay is still activated. Therefore the register will not hold the input value, effectively ignoring the register rumble.
  5. Both the enable signal and clear signals are set to 0.
  6. The clear relay is released and as a result of that, the register feedback loop is restored and the register will hold its value.
  7. The register switch is closed.

The registers are controlled by a four bit register decoder. The 15 outputs of this decoder are connected through an AND relay with the Enable left, Clear and Enable right lines. Because a copy operation involves two registers, there are two identical register controllers called Source and Destination. The outputs from the source and destination decoders for the same enable line, for instance enable left a, are connected through a diode OR port.

The instruction register


The instruction register holds the instruction that is executed. In order to handle memory problems, instructions containing all 0 or all 1 are treated as No Operation or NOP. The NOP needs to be detected in order to show this special situation as a NOP instruction. NOP detection is done by connecting diodes to the instruction register, as in principle shown in the following circuit diagram.

Two signals are generated: connected to the NC-contact, a signal is generated that is 0 when all bits are 1 and connected to the NO-contact, a signal is generated that is 0 when all bits are 0. Both signals are XOR-ed together and the NOP detection emerges. The same principle is used to determine weather the Jump base is not used (all bits are 0) or used (one or more bits are 1). 

The status register


The status register is a special register that is used for conditional jumping. It is controlled in the same way as the other registers are. Three of the statusbits in the status register are connected to the databus, one to the ALU:

The condition decoder is used to generate the two conditions. Conditions are used for conditional jumping and for instruction variants. An instruction variant is an instruction that can be executed in more (maximal 4) way’s. There are two sets of conditions basic conditions and alternative conditions. 

The basic conditions are 1. the instruction condition equals the status register and 2. the situation that bit0, bit 1 and bit2 are all zero. For the alternative conditions, bits 0 and 1 are used. This is shown in the next circuit diagram.


Januari 2019, Jeroen Brinkman